manualshive.com logo in svg

JUKI APW-896/IP-420, Instruction Manual, Page: 85 / 140

Share
Download
JUKI APW-896/IP-420 Instruction Manual Download Page 85

− 81 −

a. 

Locksttch ptch

b. 

Condensaton/back tack at sewng start selecton

c. 

Condensaton/back tack at sewng end selecton

d. 

Dart stretcher stop/motion change-over

3

  Register the sewing data to SEWING DATA CUSTOMIZING 

button

 

Up to 4 sewing data can be registered to SEWING DATA 
CUSTOMIZE buttons 

N

.

 

Register and use the sewing data that are frequently used.

 

When pressing CUSTOMIZING button 

N

 you desre to regster, 

the sewing data list (screen A) is displayed.

4

  Select the sewing data to be registered

 

Select the sewing data you desire to register with SEWING DATA 

button 

O

.

 

When the selected button s pressed twce, the selecton s 
released.

The data below have been registered in order from the left at the time of your purchase.

O

N

Sewing data list screen

(Screen A)

P

5

  Register the data to the customizing button

 

When ENTER button  

 

P

 s pressed, regster to the 

customzng button ends, and the screen returns to the 

customizing screen of the input screen. The registered sewing 
data is displayed on CUSTOMIZING button 

N

.

Summary of Contents for APW-896/IP-420













































































































































Reviews:

No comments