manualshive.com logo in svg

JUKI APW-896/IP-420, Instruction Manual, Page: 130 / 140

Share
Download
JUKI APW-896/IP-420 Instruction Manual Download Page 130

− 126 −

Error code

Description of error

How to recover

A203

Oil replacement time warning

When operation time of the sewing machine is reached to the oil 
replacement time that is set from the panel.

Possible to 
re-start after 

reset.

E220

Grease-up warning

When number of stitches of operation is reached to 40 million 

sttches.

Possible to 
re-start after 

reset.

E221

Grease-up error

When number of stitches of operation is reached to 48 million 

sttches, a sewng mpossble state occurs.

＊

 After applying grease, it is possible to release when clearing 

memory swtch 

 Number of stitches of grease-up.

Possible to 
re-start after 

reset.

E303 

Semilunar plate sensor error

Detection of upper dead point of the sewing machine cannot be 
performed.

Turn OFF the 
power.

E349

Step-out detection sensor does not react.

For the emergency procedure, t s possble to contnually use by 

re-starting with the reset button.

However, check the sensor and be sure to replace t when t s 

defective.

Possible to re-
start after rest.

E351

Reflecting tape for detecting angle has been deteriorated.  

Possible to 
re-start after 

reset.

E353

Angle detection sensor fails to detect.  

＊

Clean dust on the reflecting tape of the flap base with an air 

gun.

Possible to 
re-start after 

reset.

E354

Angle detection sensor forced stop

Possible to 
re-start after 

reset.

E355

Angle detection sensor dust detection

＊

Clean dust on the reflecting tape of the flap base with an air 

gun.

Possible to 
re-start after 

reset.

E356

Angle detection sensor front end fails to detect.

Possible to 
re-start after 

reset.

E357

Corner knife on the moving side, left is held lifted.

Possible to 
re-start after 

reset.

Summary of Contents for APW-896/IP-420













































































































































Reviews:

No comments