manualshive.com logo in svg

JUKI APW-896/IP-420, Instruction Manual, Page: 135 / 140

Share
Download
JUKI APW-896/IP-420 Instruction Manual Download Page 135

− 131 −

Error code

Description of error

How to recover

E478

Deflection direction of corner knives on the moving side 

error

Possible to 
re-start after 

reseat.

E479

Deflection direction of corner knives on the fixing side error

Possible to 
re-start after 

reseat.

E480

Max. value of clearance between corner knives on the 

moving side error

Possible to 
re-start after 

reseat.

E481

Max. value of clearance between corner knives on the fixing 

side error

Possible to 
re-start after 

reseat.

E482

Range of flap angle detection is exceeded.

Possible to 
re-start after 

reseat.

E483

Input deflection amount exceeds the limit.

Possible to 
re-start after 

reseat.

E484

Zipper attaching data cannot be sewn.

Possible to 
re-start after 

reset.

E485

Data other than zipper attaching data cannot be sewn.

Possible to 
re-start after 

reset.

E486

Flap sewing data cannot be sewn.

Possible to 
re-start after 

reset.

E487

Both long presser and endless zipper are simultaneously 

selected.

Possible to 
re-start after 

reset.

E488

- - - 

The gauge size exceeds the input range.

Possible to 
re-start after 

reset.

Summary of Contents for APW-896/IP-420













































































































































Reviews:

No comments