JUKI APW-896/IP-420 Instruction Manual Download Page 76

Page: 76 / 140

− 72 −

No.

Item

Setting range

Edit unit

Initial value

Corner knife motor origin compensation

Origin of corner knife motor is compensated.

−5.0 to

5.0

0.1mm

0.0mm

Marking light origin compensation (just under)

Origin of marking light motor is compensated. Origin is in the state that

it irradiates light just under and located at the position of 230 mm from

needle.

−500 to

500

1pulse

0pulse

Marking light origin compensation (needle side)

Position of needle side from origin of marking light motor is

compensated. Light irradiation position is 80 mm from needle.

−500 to

500

1pulse

0pulse

Marking light origin compensation (operator side)

Position of operator side from origin of marking light motor is

compensated. Light irradiation position is 380 mm from needle.

−500 to

500

1pulse

0pulse

Back tack motor origin compensation

Origin of back tack motor is compensated.

−30 to 30

1pulse

0pulse

Summary of Contents for APW-896/IP-420













































































































































Search results

Summary of Contents for APW-896/IP-420

Reviews:

JUKI APW-896/IP-420, Instruction Manual, Page: 76 / 140

Search results

Summary of Contents for APW-896/IP-420

Reviews: