3-81
[6] Process Switch Range
•
Set the boundary range of a specific area.
•
This function is enabled when Range Fix is selected in
[4]
Process Switch.
•
The specific area turns out to be a circle with the own ship’s position as the center.
•
The boundary range can be set in units of 0.1 nm, ranging 0.1 to 25.5 nm.
[7] Fast Target Detection
•
This function displays fast moving targets that are suppressed in scan-correlative process mode.
•
This function is enabled when 3Scan CORREL , 4Scan CORREL , or 5Scan CORREL is
selected as the video process mode.
•
If unwanted waves remain of the display, suppress them by using the
[SEA]
,
[RAIN]
, or
[GAIN]
dial, or adjusting the interference rejection mode.
Off : Disables the Fast Target Detection function.
On : Enables the Fast Target Detection function.
3.8.2 Set Radar Trails (RADAR Trails Setting)
This function enables the setting of detail information about radar trails processing.
Procedures
1 Press the [TRAILS] key for 2 seconds.
The RADAR Trails Setting menu will appear.
Detail data about radar trails processing can be set by changing the settings of each
menu item.
Note:
After the settings for radar trails processing are changed, targets’ trails may not be displayed or
trails may be plotted with unwanted waves. Thus, do not make a significant change in the
settings.
[1] Trails Mode
•
Set the radar trail display mode.
•
For details on the trail mode, see Section 3.4.8.
[2] Trails Reference Level
•
Select a radar video threshold level required for plotting radar trails.
•
The radar video threshold level increases in order of
Level1
→
Level2
→
Level3
→
Level4 .
•
To plot radar trails with unwanted waves, change to a higher level.
•
To thin radar trails, change to a higher level.
•
If radar trails are plotted in snatches, change to a lower level.
Summary of Contents for JMA-5912-6
