background image

3.2. Wind speeds

Wind speed averaged over 10 minutes at a height of 10 m

Wind

Force

Above flat ground

Characteristics

m/s

Wind type

0

0.0 - 0.2

Calm

Calm, smoke rises vertically or nearly
vertically

1

2

0.3 - 1.5

1.6 - 3.3

Slight breeze

Wind direction recognisable from smoke
plumes, the wind begins to be noticeable on
the face; leaves begin to rustle and weather
vanes can start to move.

3

4

3.4 - 5.4

5.5 - 7.9

Moderate wind

Leaves and twigs in continuous movement,
small branches begin to move. Dust and
paper begin to move over the ground.

5

8.0 - 10.7

Fairly strong
wind

Small leaved branches make swaying
movements; crested waves form on lakes
and canals.

6

10.8 - 13.8

Strong wind

Large branches move; you can hear the
wind whistling in telephone wires; umbrellas
can only be held with difficulty.

7

13.9 - 17.1

Severe wind

Entire trees move; the wind causes difficulty
when you walk into it.

8

17.2 - 20.7

Stormy wind

Twigs break off, walking is difficult.

9

20.8 - 24.4

Storm

Causes superficial damage to buildings
(chimney pots, roof-tiles, and TV antennae
are blown off).

10

24.5 - 28.4

Severe storm

Uprooted trees; considerable damage to
buildings etc. (occurs infrequently on land).

11

28.5 - 32.6

Very severe
storm

Causes extensive damage (occurs very infre
quently on land).

12

> 32.6

Hurricane

3.3. Noise declaration

The  following  values  for  emitted  noise  may  be  taken  as  general  and  conservative  values  for
ordinary  installations  of  loader  cranes  on  normal  diesel  engine  powered  trucks.  Declared  dual-
number noise emission values in accordance with ISO 4871:

• Emitted  A-weighted  sound  power  level  for  basic  loader  cranes  in  accordance  with  ISO  3744:

LwA = 103 dB (Uncertainty: KwA = 2 dB).

• Emitted A-weighted sound power level for loader cranes with hoist in accordance with ISO 3744:

LwA = 107 dB (Uncertainty: KwA = 2 dB).

• A-weighted sound pressure level at loader crane control stations in accordance with ISO 11201:

LpA = 95 dB (Uncertainty: KpA = 4 dB).

Safety precautions and warnings

22

Jonsered 1188S CE

Summary of Contents for 1188S CE

































































































Reviews: