Jonsered 1188S CE Operator'S Manual Download

Page: 91 / 96

13. Diesel heater [Option]

13.1. Diesel heater [option]

Factory mounted heater has a switch at the control panel inside the cabin. It is possible to install a
separate switch inside the vehicle cab.

Start the diesel heater

Turn the switch (1) clockwise to activate the heater. The
temperature is adjustable from +10°C to + 40°C, when
correct temperature is reached, the output is reduced.

NOTE

It takes about three minutes for the heater to start up. If necessary, the starting
process can be repeated.

The switch is stepless. A delay for the adjustment can occur.

Turn the switch (2) to adjust the speed of the fan. The fan is adjustable in four steps, off = 0 ,
slow=1, medium = 2 and fast =3.

Stop diesel heater:

Turn the switch (1) anticlockwise to turn off the heater.

DANGER

It is not allowed to use the power supply to turn off the heater.

Diesel heater [Option]

Jonsered 1188S CE

Summary of Contents for 1188S CE

































































































Search results

Summary of Contents for 1188S CE

Reviews:

Related manuals for 1188S CE

Brands by name

Popular brands

Jonsered 1188S CE, Operator'S Manual

Search results

Summary of Contents for 1188S CE

Reviews:

Related manuals for 1188S CE

Brands by name

Popular brands