Jonsered 1188S CE Operator'S Manual Download Page 57

Page: 57 / 96

NOTE

Pressure in the hoses can prevent the quick couplings from connecting: You can
release the pressure

- by pressing open the quick-acting coupling’s stem

- from the pressure gauge adapter, using a suitable connector.

9.3. Electric tiltable seat [option]

To operate the seat up or down.

Push and hold button (1) and operate the switch (2) at the
same time.

WARNING

Do not stand in front of moving parts. They can cause injuries.

Operating the stabiliser system

WARNING

All levers must be in neutral position.

DANGER

When you are operating the stabiliser extensions: Make sure that you have full
view of the stabiliser extensions. Do not stand in front of hydraulically operated
stabiliser extensions.

Starting crane operation

Jonsered 1188S CE

Summary of Contents for 1188S CE

































































































Search results

Summary of Contents for 1188S CE

Reviews:

Related manuals for 1188S CE

Brands by name

Popular brands

Jonsered 1188S CE, Operator'S Manual

Search results

Summary of Contents for 1188S CE

Reviews:

Related manuals for 1188S CE

Brands by name

Popular brands