manualshive.com logo in svg

JJ-CCR CE Edition, User Instructions

Share
Download
JJ-CCR CE Edition User Instructions Download Page 57

JJ-CCR ApS 2017

www.JJ-CCR.com

2017 JJ-CCR ApS –  2.00 / Revision 06

57

Next, the helium content of the gas is set. Only one digit of the number is changed at a time. The ten’s 
are always set first. Pressing the left button ”Change” results in the displayed digit being increased by 1. 
After the digit has reached 9 it will revert back to 0 again. Pressing the right button (Next) once takes the 
diver to the units digit.

Upon arriving at the units digit for the helium content it is possible to save the gas data by pressing the 
right button ”Save”.

Pressing the left button ”Next Gas” switches to the next gas. If the gas number is preceded by an ”A” 
then this is the current active gas. It is possible to adjust this but not to delete it (0% O2 and 0% HE).

If all 5 gases have been displayed then the user automatically arrives back at the menu item ”Define Gas”.

Summary of Contents for CE Edition













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands