background image

 

 

Extension table assembly

 

Attach the extension bracket (E, Fig. 
6) to the side of the motor (D) with 2 
socket head cap screws (F). 

 

Fig 6 

Slide the shaft of the extension table 
(C) into the extension bracket and 
tighten with lock knob (G). 

 

5.3 Mains connection 

Mains connection and any extension 
cords used must comply with 
applicable regulations. 
The mains voltage must comply with 
the information on the machine 
licence plate.  

The mains connection must have a 16 
A surge-proof fuse. 

Only use power cords marked 
H07RN-F 

Connections and repairs to the 
electrical equipment may only be 
carried out by qualified electricians.  

In case of machine overload the motor 
overload cut-off will react. 
After appr.5 min of cooling the 
overload cut off can be reset. 

Attention: The machine will start 
when you reset the overload push 
button! 
(Only 230V version) 

5.4 Dust connection 

Before initial operation, the machine 
must be connected to a dust extractor. 
The suction should switch on 
automatically when the belt sander is 
switched on. 

The flow rate on the suction port must 
be 20m/sec. 
Flexible hoses must be of non-
flammable quality, and must be 
connected to the machine ground 
system. 
 

5.5 Starting operation 

You can start the machine with the 
green on button. The red button on the 
main switch stops the machine. 

After connecting to the power source, 
turn on the power to the machine just 
enough to start the belt rotating and 
then turn off.  Do this several times 
and observe belt tracking. 
If adjustment is necessary refer to 
“Belt tracking adjustment” (chapter 
7.2) 
 

6.  Machine operation 

6.1 Horizontal sanding 

With the sanding platen locked in the 
horizontal position, the removable 
fence (A, Fig. 7) may be used.  
The fence can be secured in place by 
screwing two lock knobs (B) into the 
guide blocks found in the mitre slot. 

Remove the extension table if 
applicable. 

The backstop (C) must be mounted 
and the drum guard must be closed. 

 

Fig 7 

6.2 Vertical sanding

 

With the sanding platen (E, Fig 8) 
locked in the vertical position, the 
backstop (C) must be installed. 

Remove the extension table if 
applicable. 

The drum guard must be closed. 

 

Fig 8 

Any sanding angle can be chosen. 
The adjustable 90°stop is located on 
the back of the machine. 

The mitre gauge (D) may be used. 

The machine table is adjustable in 
height (see chapter 7.5). 

Note: 

With the machine table slightly tilted 
and the workpiece moving 
longitudinally you can achieve an 
aditional oscillation and an improved 
sanding surface. 

 

6.3 Contour sanding 

Open the drum guard (A, Fig 9) and 
tighten the 2 lock knobs (D). 

 

Fig 9 

Mount the extension table (B) and 
clamp it on the desired working height 
with lock knob (C). 

The drum guard must always be 
closed if the extension table is not in 
use. 

 

 

 

 

 

 

Summary of Contents for OES-80CS



















Reviews: