Jet-tech XG-37, Operation Manual

Page: 2 / 35

Specifications :
General Plumbing [Hot water and cold water required]
• Plumb with 1/2" water supply. Adapt to 3/8" FMPT
• Minimum water pressure is 25 PSI
• Maximum water pressure is 100 PSI. Install water pressure -
regulator if line pressure is over 100 PSI. Water valve on unit
has built-in strainer and flow control to provide consistent
volume between 25 and 100 PSI
• Install separate water shut-off valve
• Unit has built-in air gap - vacuum breaker is not required
• Consumption is 3 gallons per cycle
Hot Water Supply
• Maximum temperature is 150ºF (66ºC)
• Minimum temperature is 130ºF (54ºC)
Cold Water Supply
• No minimum temperature requirement
Drain
• 1-1/2" tailpiece.
• Use open type floor drain for maximum drainage
Electrical
• 120V, single phase, 60Hz, 6-foot grounded cord included
• Dedicated 15 amp circuit recommended
• Power requirements - 3.5 amps
Detergent*
• Extra heavy duty, non-foaming, commercial liquid dishwashing
detergent is required - .30% concentration
• Consult local chemical supplier to match detergent with local
water conditions
Sanitizer*
• Liquid chlorine bleach (sodium hypochlorite - 5.25% solution)
adjusted to 50 ppm
Rinse Aid*
• Liquid Rinse Aid adjusted for proper sheeting
Operation / Capacity
• 120°F (49ºC) minimum wash temp and rinse temp adjustable
down to 75°F (24ºC)
• 2 minute 15 second cycle
• 2-3/4" diameter bar glasses - 41 per cycle
• 2-1/2" diameter bar glasses - 49 per cycle
•
•
Maximum glass height 10"
Materials
• 20 gauge stainless steel parts include: cabinet
• 18 gauge stainless steel parts include: floor and tanks
• 16 gauge stainless steel parts include: leg mounting brackets
and legs
• 11 gauge stainless steel parts include: drive wheel
Service Access
Front panel is removable for service
* Detergent, Sanitizer, and Rinse Aid containers are stored externally.
The side cut-out in the machine provides space for three one-gallon
chemical containers within the 24 “ x 2 4" foot print of the machine.
Unique drainboard top provides integrated glassware
landing area.
Covers and drainboard top are easily removable for cleaning
access.
The sliding cover prevents water and steam from escaping during
operation and reduces operating noise. Additionally, the cold water
rinse eliminates steam billowing out at the end of the cycle.
No curtain and soft-start conveyor help to ensure no glasses tip
over during operation.
Full 10” of clearance height for washing glassware and pitchers.
Can wash up to 18 glasses per minute, easily handling the output
of multiple bartenders using typical glassware. (A complete cycle
is 2 minutes, 15 seconds)
Easy to clean membrane switch
panel includes :
Conveyor advance switch that rotates conveyor
one half turn for easy loading and unloading
of glassware.
Priming switches for easy priming of chemical
pumps.
De-liming cycle for easy removal of mineral
deposits during maintenance (de-liming agent
must be added).
XG-37 is equipped with
a slide-out chemical bottle
rack for easy access
to chemical bottles.
Durable water recirculating
pump has stainless steel
housing and impeller
(shown with cover removed)
59%
LESS
WATER
87%
LESS
ENERGY
Fill and dump style cycle results in up
to 59% less water consumption than
common industry rotary glasswashers.
Fill and dump operation means no
maintenance heater and low utility bills.
Uses up to 87% less energy than
common industry rotary glasswashers.
Virtually no idle energy use.
Pumped wash and rinse ensures
water line pressure variances do not
affect wash results.
The XG-37 has a fill and dump style cycle but the comparisons to traditional fill & dump style
machines end there. In addition to the cold water rinse, this glasswasher is specifically
designed to align with underbar equipment. It also has a sliding cover for access to glassware,
which improves bartender work flow by eliminating the door extending into the aisle.
Automatic peristaltic metering
chemical pumps:
Front-mounted for easy visual
inspection.
Accurately dispense detergent,
sanitizer, and rinse aid.
Third chemical pump included for
use with rinse aid to ensure
no spotting.
Switch turns of the
machine if the cover is
slid open during the
spray portion of the cycle
to prevent over spray.
The cycle resumes if the
cover is closed within
30 seconds.
Removable front
and side panels for easy
service access.
Control board
Delays cycle start until incoming water is at least 120°F (49°C) to ensure
excellent wash results.
Allows lengthened fill time without increasing overall cycle time for installations
with less than normal water volume.
Allows 75°F (24°C) cold water rinse temperature for clean glasses that are cool
to the touch.
Permits easy chemical pump adjustments.
Slide-out circuit board tray allows for easy service access.
Optional Accessory
Export transformer 220V/50Hz electrical (price on request)