background image

 

 

 

 

 

 

 

 

 

 

VISUAL CHEMICAL DELIVERY VERIFICATION

 

The peristaltic chemical pumps are located in the base of the dishwasher. They 
feature a transparent cylinder (1) to visually see if fluid is passing through the 
pumps. The pumps are automatically energiz

ed during the “initial fill” (when 

turning on the dishwasher) and “rinse cycle” (after the wash cycle). During this 
time, the flow indicator (2) will move between the “Min Flow” position and the 

“Max Flow” position (3) in the cylinder. It is normal for the pumps to cycle on and 
off.

 

If the flow indicator (2) does not move during the fill or rinse, no fluid is 
circulating through the pump. It is recommended not to use the dishwasher until 
this condition is resolved.

 

 

 
 
 
 
 
 
 

RINSE PRESSURE

 

30 PSI

 

 

 

 

RINSE FLOW INDICATOR

 

 

 

DETERGENT FLOW INDICATOR

 

 
 
 
 
 
 

 

TROUBLESHOOTING

 

1. Ensure that there is sufficient chemical in the container and that the tube is not kinked. The filter 
on the end of the tube must reach to the bottom of the container. If the filter or tube is blocked, 
remove and soak in warm water to dislodge the obstruction.

 

2. There may be air in the pump. T

o “Prime” the pumps (remove the air), turn off and drain the 

dishwasher. Replace the drain tube, close the door and turn on the dishwasher. The pumps will be 
activated as the machine fills. The Flow Indicators (2) should start to move by the time the machine 
has filled. If not, repeat the drain and fill.

 

3. The Squeeze Tube (flexible tube inside the pump) is worn or perforated. This part is a normal wear 
and tear item that must be replaced periodically (when pump performance diminishes). Call for 
Service.

 

4. The pump does not operate - the roller in the middle of the pump does not turn during the fill or 
rinse. Call for Service.

 

For any other request on set-up and installation, please contact us toll free at 1 888 275 4538 
extension 611 or (+1 514) 737-9701 (International)

 

IMPORTANT: Remember to always use caution and protective gear whenever you are manipulating 
chemicals. They can burn the skin. Follow the manufacturer

’s instructions carefully.

 

 
 

 

10

 

Summary of Contents for 727E

















Reviews: