JESS WELDING inoMIG 350, Operating Instructions Manual

Page: 79 / 112

inoMIG 350/400/500 10 Operation/welding
BA-0014 • 2020-06-05
EN - 25
10.16 Fx options (MC1)
This function can be used to change the lower-level basic settings. Press and hold the Fx operating button
(for more than 1 second) to access the options. The following options can be changed:
• EC 1/2: Select the functions for the remote control potentiometer (see 10.23 on page EN - 26)
• Hold: Set the display hold time in seconds (0 = infinite to 25 s)
• Reset the control system/memory locations (see next point)
• Set the torch type and length: Tap until “tch” appears on the left-hand display. The following 3-digit
number appears in the middle display: First digit: 1 = gas-cooled torch, 2 = water-cooled torch;
second and third digits: Length of the torch in meters (2, 3 or 4 m). Use the knob to set the connected
torch type accurately
Example: 204 = water-cooled torch with a length of 4 m
• Enter the remaining cable lengths (earth cable and intermediate cable assembly): tap until “cbl” is
displayed in the left-hand display and then enter the total length of all cables (not including the torch
length!) in the right-hand display. (The cable cross-section used as a basis appears in the middle
display, e.g. 35 mm²)
Example: 12 = total cable length of 12 m (maximum 40 m possible)
To save the new settings, exit options menu by tapping the “Drahteinfädeln” (Wire feed) button.
10.17 Accessing and saving jobs (MC1)
100 user-specific jobs can be stored in the control box. To open the job menu, briefly tap the “JOB laden”
(Load job) operating button. “Job” appears on the left-hand display.
The middle display indicates the status of the memory location. This can be:
The job number appears on the right-hand display. Once the job menu is open, the middle knob can be used
to select the desired memory location. You can now either load a job that has already been saved by
tapping the “JOB laden” (Load job) operating button or save the current settings by tapping the “Speichern”
(Save) operating button (the symbol == appears on the middle display). To overwrite a memory location,
press the “save” operating button for more than 1 second.
10.18 Coolant – flow display (MC1)
To display the current flow of coolant in the cooling circuit, press the “l/m” operating button. The “l/min”
LED illuminates and the current value is shown in the right-hand display (e.g. 1.45). If the flow drops below
the minimum flow value of 0.25 l/m for more than 5 seconds, the error “Err H2o” is displayed. Welding is
no longer possible at this point. The machine must be switched off. If the shortage of water is eliminated,
normal operation of the machine can re-commence.
10.19 Deleting jobs/factory setting (MC1)
The control system has two separate options:
1. Delete all jobs saved by the user (display: “rES 1 – Job”) or
2. Reset the entire control system to the factory settings (display: “rES 2 – ALL”).
1
To use these options, press and hold the Fx button until EC 1 appears on the display. Now tap the Fx
button several times until “rES 1 – Job” appears on the display.
2
Turn the middle knob to select “rES 1” or “rES 2”.
3
Press and hold the “Gastest” (Gas test) button until “clr” disappears from the right-hand display.
4
The procedure is now complete.
NOTICE
The torch type and cable length must be precisely set in order for the control system to work optimally.
Incorrect values can lead to a non-optimal welding result.
free Memory location free
used
Memory location used
== The data for this memory location are currently being loaded