manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 356

5.7L/Automatic (Over-

land)

4x2

12,200 lbs (5 534 kg)

64 Sq. Ft. (5.95
square meters)

7,395 lbs (3 354 kg) 740 lbs (336 kg)

5.7L/Automatic

4x4

12,200 lbs (5 534 kg)

64 Sq. Ft. (5.95
square meters)

7,200 lbs (3 266 kg) 720 lbs (327 kg)

3.0L Diesel/Automatic

4x2

12,200 lbs (5 534 kg)

64 Sq. Ft. (5.95
square meters)

7,400 lbs (3 357 kg) 740 lbs (336 kg)

3.0L Diesel/Automatic

4x4

12,200 lbs (5 534 kg)

64 Sq. Ft. (5.95
square meters)

7,200 lbs (3 266 kg) 720 lbs (327 kg)

Refer to local laws for maximum trailer towing speeds.

NOTE:

The trailer tongue weight must be considered as

part of the combined weight of occupants and cargo, and
should never exceed the weight referenced on the Tire
and Loading Information placard. The addition of pas-
sengers and cargo may require reducing tongue load and

Gross Trailer Weight (GTW). Redistributing cargo (to the
trailer) may be necessary to avoid exceeding Rear Gross
Axle Weight Rating (GAWR) of 3,200 lbs (1 451 kg). Refer
to “Weight Distributing Hitch” in this section. Refer to
the “Tire–Safety Information” section in this manual.

356

STARTING AND OPERATING

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands