manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 158

Courtesy/Reading Lights

At the forward end of the console are two courtesy/
reading lights.

Press the lens to turn these lights on. Press a second time
to turn the lights off.

The lights also turn on when a front door or rear door is
opened. The lights will also turn on when the unlock
button on the remote keyless entry transmitter is pressed.

Sunglasses Storage

At the rear of the console a compartment is provided for
the storage of a pair of sunglasses.

The storage compartment access is a

9

push/push

9

design.

Push the finger depression on the overhead console to
open. Push the finger depression to close.

GARAGE DOOR OPENER — IF EQUIPPED

HomeLink

t

replaces up to three remote controls (hand

held transmitters) that operate devices such as garage
door openers, motorized gates, lighting, or home security
systems. The HomeLink

t

unit operates off of your vehi-

cle’s battery.

NOTE:

HomeLink

t

is disabled when the Vehicle Secu-

rity Alarm is active.

158

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands