manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 319

2. Economy—
Improper inflation pressures can cause uneven wear
patterns to develop across the tire tread. These abnormal
wear patterns will reduce tread life resulting in a need for
earlier tire replacement. Under inflation also increases
tire rolling resistance and results in higher fuel consump-
tion.

3. Ride Comfort and Vehicle Stability—
Proper tire inflation contributes to a comfortable ride.
Over inflation produces a jarring and uncomfortable ride.
Both under inflation and over inflation affect the stability
of the vehicle and can produce a feeling of sluggish
response or over responsiveness in the steering.

Unequal tire pressures can cause erratic and unpredict-
able steering response.

Unequal tire pressure from side to side may cause the
vehicle to drift left or right.

Tire Inflation Pressures

The proper cold tire inflation pressure is listed on either
the face of the driver’s door or the driver’s side “B” pillar.

The pressure should be checked and adjusted as well as
inspecting for signs of tire wear or visible damage at least
once a month. Use a good quality pocket-type gauge to

Tire Placard Location

STARTING AND OPERATING

319

5

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands