manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 150

and will only activate when the vehicle is descending a
hill. It will usually not activate on level ground.

The HDC speed may be adjusted by the driver to suit the
driving conditions. The speed corresponds to the trans-
mission gear selected.

•

1st = 1 mph (1.6 km/h)

•

2nd = 2.5 mph (4 km/h)

•

3rd = 4 mph (6 km/h)

•

4th = 5.5 mph (9 km/h)

•

5th = 7.5 mph (12 km/h)

•

Reverse (R) = 1 mph (1.6 km/h)

•

Neutral (N) = 2.5 mph (4 km/h)

•

Park (P) — HDC will not function

HDC also has the capability to sense rough terrain, and
will automatically adjust to a slightly slower set speed
(about.3 mph (.5 km/h) than normal.

HDC operation can be overridden with brake application
to slow the vehicle down below the HDC control speed.
Conversely, if more speed is desired during HDC control,
the accelerator pedal will increase vehicle speed in the
usual manner. When either the brake or the accelerator is
released, HDC will control the vehicle back to the origi-
nal set speed.

HDC is intended for low speed off-road driving only.
At vehicle speeds above 30 mph (48 km/h), HDC will no
longer function. When the vehicle speed drops below 30
mph (48 km/h), HDC function will automatically resume
and the vehicle speed will return to the chosen set speed.

150

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands