manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 327

decrease. Tire pressure should always be set based on
cold inflation tire pressure. This is defined as the tire
pressure after the vehicle has not been driven for at least
3 hours, or driven less than 1 mile (1 km) after a 3 hour
period. Refer to the “Tires – General Information” in
this section for information on how to properly inflate
the vehicle’s tires.

The tire pressure will also increase as

the vehicle is driven - this is normal and there should be
no adjustment for this increased pressure.

The TPM System will warn the driver of a low tire
pressure if the tire pressure falls below the low pressure
warning threshold for any reason, including low tem-
perature effects, or natural pressure loss through the tire.

The TPM System will continue to warn the driver of low
tire pressure as long as the condition exists, and will not
turn off until the tire pressure is at or above recom-
mended cold tire pressure. Once the low tire pressure
warning has been illuminated, the tire pressure must be

increased to the recommended cold tire pressure in order
for the “Tire Pressure Monitoring Telltale Light” to be
turned off. The system will automatically update and the
“Tire Pressure Monitoring Telltale Light” will extinguish
once the updated tire pressures have been received. The
vehicle may need to be driven for up to 10 minutes above
15 mph (24 km/h) to receive this information.

For example, your vehicle has a recommended cold
(parked for more than 3 hours) tire pressure of 33 psi (227
kPa). If the ambient temperature is 68°F (20°C) and the
measured tire pressure is 28 psi (193 kPa), a temperature
drop to 20°F (-7°C) will decrease the tire pressure to
approximately 24 psi (165 kPa). This tire pressure is
sufficiently low enough to turn ON the “Tire Pressure
Monitoring Telltale Light.” Driving the vehicle may cause
the tire pressure to rise to approximately 28 psi (193 kPa),
but the “Tire Pressure Monitoring Telltale Light” will still
be ON. In this situation, the “Tire Pressure Monitoring

STARTING AND OPERATING

327

5

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands