manualshive.com logo in svg

Jeep 2008 Cherokee, Owner'S Manual

Share
Download
Jeep 2008 Cherokee Owner'S Manual Download Page 155

NOTE:

The Rear Park Assist system will MUTE the

radio, if on, when the system is sounding an audio tone.

Enable/Disable the Rear Park Assist System

The Rear Park Assist System can be enabled and disabled
with a switch located on the upper switch bank of the
instrument panel.

When the switch is pressed to disable the system, the
instrument cluster will display the

9

PARK ASSIST DIS-

ABLED

9

message. Refer to “Electronic Vehicle Informa-

tion Center (EVIC)” in Section 4 of this manual. When the
shifter is changed to R (Reverse) and the system is
disabled, the instrument cluster will actuate a single
chime, once per ignition cycle, and it will display the
message.

The Rear Park Assist Switch LED will be ON when the
Rear Park Assist System is disabled or defective. The
Rear Park Assist Switch LED will be OFF when the
system is enabled.

Service the Rear Park Assist System

When the Rear Park Assist System is defective, the
instrument cluster will actuate a single chime, once per
ignition cycle, and it will display the

9

SERVICE PARK

ASSIST SYSTEM

9

message. Refer to “Electronic Vehicle

Information Center (EVIC)” in Section 4 of this manual.

Rear Park Assist Switch

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

155

3

Summary of Contents for 2008 Cherokee











































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands