background image

38

58

7

Index 1

plumbing

WATER TANK FILLING

In order to avoid handling mistakes, never fill the water and fuel tanks at the same time. 
During filling, avoid handling contaminants near the filling plugs. 
Open and close the filling plugs with the special key or winch handle. 
Check the filler plug seals for condition during filling.
The tanks are fitted with overflow outlets and vents.

To prevent a pressure build-up in the system, never press the water filling hose deep into
the system.

RECOMMENDATION / MAINTENANCE:

Monitor the quality of drinking water taken on board at remote locations.

The tanks can be sterilized by adding a “clonazone” tablet  

(available from pharmacies).

Purify the tanks and pipes with acetic acid or white vinegar if the boat 

is to stay unmanned for a long period.

Inspection ports are provided on tanks, through which internal cleaning 

can be performed.

Don’t use chlorine-based products. These products may spoil the quality of the tank

stainless steel.

Refer to chapter 11 for winter precautions.

Note 

The capacity of the water tank indicated on the page « Specifications » may

not  completely be used according to the trim and load of the boat.

P R E C A U T I O N

P R E C A U T I O N

- Never run the water system if the valve to the feed tank is closed

or if the tank is empty to avoid damaging the water pump. 

- Regularly check the water filter for condition as instructed in the manufacter ’s

manual. 

- Ensure that the empty tanks valve is closed.

P R E C A U T I O N

P R E C A U T I O N

Shore water supply

- Don’t switch on the water unit if the shore water tap is connected and on.

- Turn off the shore fresh water tap in case you are away.

FRESH WATER SYSTEM

Summary of Contents for sun odyssey 54 DS




















































































































Reviews: