13
FNS-0002-060-EN January 2017 Rev F
Operator Do's and Don'ts
Do's
Don'ts
Unplug juicer before opening juicing component
door
DO NOT open juicing component door before
unplugging
Stop juicer when cups are in most open position
DO NOT stop juicer when cups are in closed
position
Use light water spray when rinsing juicer
DO NOT use high pressure or volume water when
rinsing juicer
When hopper cleaning, use spray bottle and damp
towel
When hopper cleaning, DO NOT use chemical
dosage and water system
Use spray bottle with cleaner on main frame
casting in juicing components area
DO NOT use chemical dosage and water system
to clean main casting (can result in mechanical
damage)
Rinse sanitizer off juicer five minutes after applying
DO NOT leave sanitizer on juicer without rinsing
(can damage aluminum)
Use fruit within size range (2-1/2" to 3-7/8"
diameter)
DO NOT use oversized fruit
Use fruit within size range (2-1/2" to 3-7/8"
diameter)
DO NOT use small fruit
(can result in double feed and cause cups to break)
Inspect and test safety switches and door locks
weekly
DO NOT use juicer if safety switches are not work
properly
Install juicing components using spanner tool;
tighten spanner nuts and screw from top to bottom
DO NOT hand tighten spanner nuts and screw
(can result in major equipment damage)
Install orifice tube into slot on lower arm
(see Figure 6 on Page 19)
DO NOT install orifice tube on top of lower arm slot
(see Figure 6 on Page 19)
Inspect cutter daily.
Replace if damaged; adjust and tighten screw
If cutter is damaged, loose or dull, juice quality and
yield can be impacted
Mix juice and pulp slowly to reduce foam in
reservoir
DO NOT mix juice quickly in reservoir (can result in
foam and off flavor)
Summary of Contents for FRESH'N SQUEEZE
