JBT FRESH'N SQUEEZE Operators & Service Manual Download Page 33

Page: 33 / 80

FNS-0002-060-EN January 2017 Rev F

CAUTION: IF SETTING IS TOO HIGH, MOTOR CAN BURN UP.

Troubleshooting (continued)



Juicer starts, but shuts off

1. Building circuit breaker is not rated for 20 Amps.

2. Extension cord or wiring is too long.

Shorten extension cord or use heavier gauge wire.
(See Page 6 "Electrical Specifications")

3. All covers not completely closed (including cart).

Juicer may be flexing when squeezing fruit, causing switch to open. Make sure all latches are
completely locked.

Amperage setting on motor starter on machine set too low.

See Page 28 under "Juicer will not start" for removing covers.
The dial next to OFF button should be set to 14.



Juicer stalls trying to squeeze fruit

1. Fruit has part of stem on it.

Turn off Juicer. Remove fruit from the Juicer and restart.

2. Peel is too thick.

Turn off Juicer. Remove fruit from the Juicer and restart.

3. Cutter is damaged.

Sharpen or replace cutter as specified in Maintenance section.

CAUTION: CUTTER AND KNIVES ARE SHARP.

Install red protective cap onto cutter.
After red protective cap is installed, remove cutter. Handle cutter with care to avoid
direct contact with sharp edge.



Juicer runs with covers open or off

1. Defective interlock switch. Replace immediately.

See Page 28 under "Juicer will not start" for removing covers.



Juicer emits "squealing" sound during operation

1. Lubricate grease fittings on machine.

If noise continues, rod end or bearing may be defective.
See Rebuilding section to replace bearings.



Scraping noise coming from hopper area

1. Fruit lift mechanism is dragging on hopper.

See Page 26, Item 8 under "Periodic inspection".

Summary of Contents for FRESH'N SQUEEZE

















































































Search results

Summary of Contents for FRESH'N SQUEEZE

Reviews:

Related manuals for FRESH'N SQUEEZE

Brands by name

Popular brands

JBT FRESH'N SQUEEZE, Operators & Service Manual

Search results

Summary of Contents for FRESH'N SQUEEZE

Reviews:

Related manuals for FRESH'N SQUEEZE

Brands by name

Popular brands