10
FNS-0002-060-EN January 2017 Rev F
Operating Instructions
Equipment Check
Before
plugging
the
Multi-Fruit Juicer
into
an
electrical
outlet, the
following
steps
must
be
performed:
1.
Locate
the
Multi-Fruit Juicer
on
a
level
surface.
This will prevent fruit feed problems.
CAUTION
:
WHEN MOVING JUICER, ALWAYS TRANSPORT ON LEVEL SURFACE.
USE RAMPS IF NECESSARY. AVOID LEDGES, IRREGULAR FLOORS
OR DRAIN INDENTIONS. TO AVOID TIPPING, NEW JUICER UNITS ARE
SHIPPED WITH BRACING RAILS. UNITS IN THE FIELD CAN BE
UPGRADED USING THE BRACING RAIL KIT.
SEE FIGURE 5 FOR INSTALLATION INFORMATION.
2.
Lock both rear casters.
To lock, push down on caster with foot. To unlock, push again with foot.
3.
Check waste container.
Open cart door to verify that waste container is in place. A plastic bag may be
attached to the hooks above the waste container (30 gallon capacity or equivalent).
4. Check juicing components.
a. Twist and pull juice nozzle off.
b. Use key to unlock juicing components cover. Open cover and check that juicing
components are installed and securely fastened. See Figure 3, Page 9.
5.
Close and lock all access covers.
There are 4 separate access covers: hopper cover, juicing components cover, cart
door (cover) and back cover.
NEVER
operate juicer unless all covers are in place.
6. Replace juice nozzle. Wet the o-ring before installing the nozzle.
7. Make sure juice reservoir is firmly in place.
8. Make sure juice reservoir valve is in closed position.
9.
Check the hopper for foreign objects.
Remove any foreign objects found in the hopper.
10. Make sure floor area around Juicer is clean and free of obstructions and water.
Wear appropriate non-slip footwear when water is necessary.
Summary of Contents for FRESH'N SQUEEZE
