ENGLISH
OPERATION MANUAL
JB SYSTEMS®
5/58
iROCK 7S-7B
3. BUTTONS
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
4. REMOTE CONTROL INPUT:
Used to connect a optional CA-8 hand controller while the unit is used in
standalone or master/slave mode.
5. SENSITIVITY:
Used to adjust the sensitivity of the micro when the unit is used in standalone or
master/slave mode.
6. MICROPHONE:
used to trigger the internal programs to the rhythm of the music.
7. DMX INPUT/OUTPUT:
used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link
the units together.
MAIN MENU:
To select any of the pre-set functions, press
the
MENU
button up to when the required
one is shown on the display.
Select the function with the
ENTER
button.
The display will blink.
Use
DOWN
and
UP
button to change the
mode.
Once the required mode has been selected,
press the
ENTER
button to select. After 8
seconds the display will automatically return
to the main functions without any change.
To go back to the functions without any
change press the
MENU
button. The main
functions are shown on the right.
DMX512 Address Setting
Used to set the starting address in a DMX
setup.
Press the MENU button until
is
shown on the display.
Press the ENTER button, the display starts
blinking.
Use DOWN and UP buttons to change the
DMX512 address.
Once the correct address shows on the
display, press the ENTER button to save it.
(or
automatically
return
to
the
main
functions without any change after 8 seconds)
To go back to the functions without any
change press the MENU button again.
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
(2 light show) mode.
Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
ENGLISH
OPERATION MANUAL
JB SYSTEMS®
6/58
iROCK 7S-7B
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(yes blackout) or
(no blackout) mode.
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color Mode
Normal: only full colors can be selected.
Split colors: you can select full colors and 2 colors that are next to each other on the color wheel.
Press the MENU button unitl
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
(split color) mode.
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Pan Inversion
Normal: Panning movement is not inverted.
Pan inversion: Panning movement is inverted
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
(pan inversion) mode.
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Tilt Inversion (iROCK 7S) or
Barrel Rotation Inversion (iRock 7B)
Normal:
Tilt movement is not inverted.
Barrel movement is not inverted
inversion:
tilt movement is inverted
Barrel movement is inverted
Press the MENU button until
(
)
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
(normal) or
(tilt/barrel rotation inversion) mode.
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
