Japan Cach Machine TAIKO Series Service Manual Download Page 65

Page: 65 / 87

5-11

TAIKO Service Manual

CHAPTER

5-5. Maintenance Tool List

When maintenace or adjust TAIKO unit, the following parts need to be parchased.

Items

EDP#

Part#

Description

Power Supply Unit

116125

VM-30

This unit is to supply the power to TAIKO
unit.

TAIKO Harness A

127527

3280-05-54

This harness is to connect with TAIKO unit
ant Power Supply Unit.

TAIKO Harness B

116488

3280-03-11

This harness is to connect with PC and
TAIKO unit when downloding or connecting
with palm.

Clone Harness

124528

3280-05-52

This harness is to connect with a master
TAIKO and a slave TAIKO when cloning.

Reference Paper

119581

KS-070

This is a reference paper to adjust TAIKO
unit.

Summary of Contents for TAIKO Series























































































Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands

Japan Cach Machine TAIKO Series, Service Manual

Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands