Japan Cach Machine TAIKO Series Service Manual Download Page 42

Page: 42 / 87

3-7

TAIKO Service Manual

CHAPTER

3-3. Clearing a Banknote Jam

When a banknote becomes jammed inside the TAIKO unit, follow the instructions below
to remove the jammed banknote.

- Be sure to turn off the power to the TAIKO unit when opening

the upper and lower covers. Failure to do so may result in your
fingers becoming caught in the moving roller.

Open the upper lid

1. Confirm that the power to the TAIKO unit is turned off.
2. Hold in the upper cover open/close buttons and open the upper cover, then pull out the

jammed banknote.

- Be careful not to get your finger caught when closing the up-

per cover.

Open the lower lid

1. Confirm that the power to the TAIKO unit is turned off.
2. Remove the faceplate from the TAIKO unit. See =>3-1. Installation/Removal
3. Hold in the lower cover lock release buttons and remove the lower cover, then pull out

the jammed banknote.

Summary of Contents for TAIKO Series























































































Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands

Japan Cach Machine TAIKO Series, Service Manual

Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands