Japan Cach Machine TAIKO Series Service Manual Download Page 58

Page: 58 / 87

TAIKO Servic e Manual

5-4

CHAPTER

Symptom/Error Message

Possible Causes

Recovery Action

Reference paper is wrong.

Use the reference paper (KS-070)
for TAIKO.

CPU/Sensor board failure.

Replace the CPU/Sensor board.
See=> Chapter 6 Replacement
Procedure

Adjustment Error

5-2-2. Adjustment Troubles

Symptom/Error Message

Possible Causes

Recovery Action

Software does not match
with the currency.

Download the appropriate software
program to the TAIKO unit. See=>
4-1. Download

DIP Switch setting is wrong.

Set the accepting setting properly.
See=>

2-5. DIP Switch Setting

The command from Host is
set to inhibit.

Set the command to accept.

CPU/Sensor failure is
occurred.

Replace CPU/Sensor Board. See=>
Chapter 6 Replacement Procedure.

Sensor needs to be cleaned
and adjusted.

Clean all sensors. See=>

5-4.

Cleaning

Perform adjustment See=>4-2.
Adjustment

CPU board failure

Replace the CPU board. See=>

2. Replacement of CPU board

DIP Switch setting is wrong.

Set the DIP Switch No.1 ON and
supply the power to the TAIKO unit.

DIP Switch is broken.

Perform the DIP Switch TEST.
See=>

5-3-2. DIP Switch Test

Details

If the test result is NG, replace the
CPU board. See=>

6-2. Replace of

CPU board

CPU board failure

Replace the CPU board. See=>

2. Replace of CPU board

Cannot enter the Test Mode.

Motor rotates a few times

and stop.

All bills are returned.

Summary of Contents for TAIKO Series























































































Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands

Japan Cach Machine TAIKO Series, Service Manual

Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands