Japan Cach Machine TAIKO Series Service Manual Download Page 45

Page: 45 / 87

4-3

TAIKO Service Manual

CHAPTER

JCM Power Supply Unit

(Part#: VM-30, EDP#:116125)

equivalent

TAIKO

To AC Power

Serial

Port

TAIKO Harness B

(Part#: 3280-03-11,

EDP#:116488)

(OS: Windows

(R)

98 SE/2000/XP)

TAIKO Harness A
(Part#:3280-05-54,

EDP#: 127527)

Interface

Connector

Maintenance
Connecotr

Interface

Connector(10 Pin)

Maintenance

Connecotr(4 Pin)

Host Machine

ID-003/CC TALK/HII

Connector

4-1-2. Connecting Procedure

1. Set the DIP switch Nos.1, 7 and 8. DIP switch is located on the right side of TAIKO

unit.

2. Connect TAIKO unit, PC and JCM Power Supply unit (VM-30) as shown below.

3. Turn the power of the JCM power supply unit ON to turn on the power to the TAIKO

unit.

4. Confirm the TAIKO’s green LED lamp is flashing.

Summary of Contents for TAIKO Series























































































Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands

Japan Cach Machine TAIKO Series, Service Manual

Search results

Summary of Contents for TAIKO Series

Reviews:

Related manuals for TAIKO Series

Brands by name

Popular brands