SW-4000T-10GE
— 59 —
Package contentsCamera
body (1)
Sensor protection cap (1)
Dear Customer (sheet) (1)
Design and specifications are subject to change without notice.
Approximately 30 minutes of warm-up are required to achieve these specifications.
About the verified performance temperature
Make sure the following temperature conditions are met when operating the unit.
1) The camera's internal temperature sensor detects temperatures of 98 °C or less during
operation.
If the above temperature conditions are exceeded, take measures to dissipate heat according to
your installation environment and conditions.
Caution
12pin
Input range: DC +10V 〜+ 25V
consumption: 13.7 W(typ.)
(at 12 V input, full pixel, Default setting, Environmental
temperature 25°C) (Typical)
19.3 W
(Maximum)
PoE+
IEEE802.3at compatible
Support for Layer 1 classification only
Input range: +42V 〜+ 57V
consumption: 15.3 W(typ.)
(at full pixel, Default setting, Environmental
temperature 25°C) (Typical)
21.7 W
(Maximum)
RJ-45
Ethernet standards and the cable type and the maximum cable
length.
1000 Base-T : Cat5e, Cat6, Cat6e, Cat6A, Cat7
2.5G Base-T : Cat5e, Cat6, Cat6e, Cat6A, Cat7
5G Base-T : Cat6, Cat6e, Cat6A, Cat7
10G Base-T : Cat6*, Cat6e*, Cat6A, Cat7
*) The maximum cable length is limited to 55m.
12pin (DC IN/TRIG)
Model : HR10A-10R-12PB(71) (or equivalent)
Function: Power supply input / External trigger / External I/O
10pin (AUX)
Model
Camera side:Equivalaent to Hirose Electronic 3260-10S3 (55)
Cable side :Equivalaent to Hirose Electronic 350-10P-C (50)
Function: External tigger / External I/O
LED (Power/TRIG)
Function:Power on, trigger input indicator
Power supply voltage
PRNU
DSNU
Post-correction: Within ±1% (during 100% output)
Post-correction: Within ±5% (during 0% output)
25℃〜+ 60℃ / 20%〜 80%
(non-condensing)
Connectors / LEDs
Lens mount
M52 mount, F mount
Image porcessing
1 Pixel sensitivity correction: Pixel correction (DSNU, PRNU)
2 Shading correction: ColorShading, FlatShading
3 LUT: OFF: γ=1.0, ON: 257 points can be set
4 Gamma: 0.45, 0.5, 0.55, 0.6, 0.65, 0.75, 0.8, 0.9, 1.0 (9 steps available)
Dimensions
90 × 90 × 90 mm (WHD; excluding mount and protrusions)
Weight
830 g (Typ.)
Vibration resistance
3G(20 Hz 〜 200 Hz X-Y-Z direction)
Impact resistance
50G
Standard compliance
CE(EN61000-6-2 and EN61000-6-3)、FCC part 15 class B、 RoHS、WEEE
Flange back
M52 mount: 46.5 mm (in air), tolerance: 0 mm to –0.05 mm
F mount: 46.5 mm, tolerance: 0 mm to –0.05 mm
Operating temperature / humidity
5℃〜+ 45℃ / 20%〜 80%
(non-condensing)
Storage temperature / humidity
Summary of Contents for SW-4000T-10GE
Page 60: ...SW 4000T 10GE 60 Spectral Response Wave length nm Relative Response Wave length nm ...
Page 61: ...SW 4000T 10GE 61 Dimensions F mount SW 4000T 10GE F Dimenstional tolerance 0 3mm Unit mm ...
Page 62: ...SW 4000T 10GE 62 M52 mount SW 4000T 10GE M52 Dimenstional tolerance 0 3mm Unit mm ...