J.P. Instruments EDM-700 Pilot'S Manual Download Page 8

Page: 8 / 68

Page 4

Engine Data Management

compression will cause each cylinder to follow its own mixture and
temperature relationship such that one cylinder will reach peak before
another.

Section 2 - Displays and Controls

The EDM monitors engine temperatures and voltages, assists in adjusting
the fuel/air mixture, and helps diagnose engine malfunctions. There are
three components of the user interface:

•

Analog display including cylinder number and index dot

•

Digital display for numeric readouts and messages

•

Two front panel operating buttons.

Displays

Analog Display

The upper half of the face of the EDM is the analog display with %HP.

The following is a description of the analog display, from top to bottom.
Numbers in circles refer to features in the above diagram.

Summary of Contents for EDM-700





































































Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands

J.P. Instruments EDM-700, Pilot'S Manual

Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands