J.P. Instruments EDM-700 Pilot'S Manual Download

Page: 12 / 68

Page 8

Engine Data Management

Manual Mode
Just tap the

STEP

button.

Automatic stops. Each indexed parameter is

frozen in the digital display until you manually index to the next
parameter by tapping the

STEP

button. If no button is depressed for 15

minutes, the Automatic Mode will resume.

LeanFind Mode
Simply pre-lean, tap the

button and begin leaning.

The EDM will

assist you in finding the first cylinder to peak.

Buttons

Buttons, Front Panel

Two operating buttons control all functions of the EDM.

The term

tap

will be used to denote pressing a button momentarily. The

term

hold

will be used to denote pressing and holding a button for five

seconds or longer.

STEP

Button

Located on the lower left side near the instrument face.

•

In the Automatic mode,

tapping

the

STEP

button will stop

and change to the Manual mode. Then each

tap

of the

STEP

button will display the next parameter in the sequence.

•

In the LeanFind mode

tapping

the

STEP

button will

terminate the LeanFind mode and change to the Automatic
mode.

Secondary functions of the

STEP

button include:

•

In the Manual mode

holding

the

STEP

button will display the previous

parameters in the sequence (rapidly backwards).

•

In the programming procedures,

tapping

the

STEP

button will advance to

the next item in the list.

Summary of Contents for EDM-700





































































Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands

J.P. Instruments EDM-700, Pilot'S Manual

Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands