J.P. Instruments EDM-700 Pilot'S Manual Download

Page: 13 / 68

For Your Safe Flight

Page 9

•

When an alarm is displayed,

tapping

the

STEP

button will temporarily

delete that alarm from appearing for the next ten minutes.

•

When an alarm is displayed,

holding

the

STEP

button until the word

OFF

appears will delete that alarm from appearing for the remainder of the
flight.

Button

Located on the lower right side near the instrument face.

•

In Automatic or Manual modes,

tapping

the

button will

change to the LeanFind mode.

•

In Automatic or Manual modes

holding

the

button for

three seconds will toggle between Percentage and Normalize
views.

•

In the LF mode

holding

the

button after peak EGT is

found will display peak EGT.

•

In the LF mode

tapping

the

button will

mark

a data

record in long term memory and display will flash

SNAP

Secondary functions of the

button include:

•

In the pilot programming procedure,

holding

tapping

the

button is

used to increment or decrement parameter values and toggle between Yes
and No answers to questions.

STEP

and

Buttons

•

Holding both the

STEP

and

buttons simultaneously for

five seconds changes to the pilot programming procedure.

•

Holding both the

STEP

and

buttons simultaneously for

five seconds after entering LeanFind mode but before
beginning to lean will toggle between leaning “rich of peak”
and “lean of peak.”

•

Tapping both the

STEP

and

buttons simultaneously in

Manual mode toggles to include or exclude the displayed
parameter from the Automatic mode. It has no affect on the
displayed parameters in the Manual mode.

Summary of Contents for EDM-700





































































Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands

J.P. Instruments EDM-700, Pilot'S Manual

Search results

Summary of Contents for EDM-700

Reviews:

Related manuals for EDM-700

Brands by name

Popular brands