Ivoclar Vivadent 645983EU Operating Instructions Manual Download Page 46

Page: 46 / 80

1. Open the settings menu.

Scroll to page 2 in the home screen and press the

[Settings]

button.

3. Change the display brightness.

Press the touch button in the line "Display brightness".

2. Open the display brightness setting.

The

[Arrow]

buttons are used to scroll through the Settings menu.

Press the button until the setting "Display brightness" appears in the
display.

4. Select the desired display brightness.

Select the desired display brightness in percent and confirm the entry
with the green button or cancel the entry with the red button.

The setting was changed.

To return to the home screen, press either the

[Home]

touch button in the navigation bar or the HOME key on

the membrane-sealed keypad.

5.5 Advanced functions of the furnace / Software update

5.5.1 Settings

To reach the Settings menu, scroll to page 2 in the home screen and press the

[Settings]

button.

Example: Changing the brightness of the display

5. Operation and Configuration

Summary of Contents for 645983EU

















































































Search results

Summary of Contents for 645983EU

Reviews:

Related manuals for 645983EU

Brands by name

Popular brands

Ivoclar Vivadent 645983EU, Operating Instructions Manual

Search results

Summary of Contents for 645983EU

Reviews:

Related manuals for 645983EU

Brands by name

Popular brands