manualshive.com logo in svg

ITW Simco-Ion IQ Power Fantom, Installation And Operating Instructions Manual

Share
Download
ITW Simco-Ion IQ Power Fantom Installation And Operating Instructions Manual Download Page 5

3

IQ Power Fantom

5201292 Rev A

2. DESCRIPTION 

Simco-Ion’s IQ Power Fantom Wide Blower is a highly reliable, extended-range 

ionizing air blower designed for static elimination in many industrial applications.  

Its high power fan covers a large area with balanced ionization for rapid static 

neutralization.  The Fantom is a self-contained unit that includes variable speed fan 

control and closed-loop ion output and ion balance control.  The built-in emitter 

point cleaner provides manual, automatic, or remote cleaning to remove dust 

buildup from the emitter points.  This ensures full output of ionized air.
The Fantom features a user interface and indicators to continuously monitor 

performance.  It also supports connection to the IQ Power Control Station for 

the ultimate in remote monitoring and control.  Cables for interconnection with a 

Control Station are available by calling Simco-Ion customer service (800) 203-3419 

(refer to Section 8, Parts and Accessories).

Summary of Contents for Simco-Ion IQ Power Fantom

























Reviews:

No comments

Brands by name

Popular brands

Load more brands