ITech IT-M3300 Series Programming Manual Download

Page: 82 / 110

Trace Commands

Returns

0|1

TRACe:DATA?

This command reads all values saved in the cache.

Note

Before sending the query command TRACe:DATA?, the command TRIGger[:IMMediate]

must be sent to the instrument to trigger the instrument into data storage status. And the

argument of the command TRACe:FEED:CONTrol <NEXT|ALWays|NEVer> must be set

to NEXT or ALWays, otherwise the system will prompt an error.

Syntax

TRACe:DATA?

Arguments

None

Example

TRACe:DATA?

Returns

<NRf>,<NRf>,<NRf>.....

TRACe:FILTer[:STATe]

This command enables or disables the filter.

Syntax

TRACe:FILTer[:STATe]

Arguments

<0|1|OFF|ON>

Default value

OFF

Example

TRAC:FILT 0

Returns

0|1

Summary of Contents for IT-M3300 Series















































































































Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands

ITech IT-M3300 Series, Programming Manual

Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands