ITech IT-M3300 Series Programming Manual Download

Page: 4 / 110

IT-M3300 Programing Guide

Earth (ground) terminal

Reference
terminal

Caution, risk of electric shock

Positive terminal

Warning, risk of danger (refer
to this manual for specific
Warning

Caution

information)

Negative terminal

Frame or chassis terminal

Safety Precautions

The following safety precautions must be observed during all phases of

operation of this instrument. Failure to comply with these precautions or specific

warnings elsewhere in this manual will constitute a default under safety

standards of design, manufacture and intended use of the instrument. ITECH

assumes no liab

ility for the customer’s failure to comply with these precautions.

⚫

Do not use the instrument if it is damaged. Before operation, check the

casing to see whether it cracks. Do not operate the instrument in the
presence of inflammable gasses, vapors or dusts.

⚫

The power supply is provided with a three-core power line during delivery

and should be connected to a three-core junction box. Before operation, be
sure that the instrument is well grounded.

⚫

Make sure to use the power cord supplied by ITECH.

⚫

Check all marks on the instrument before connecting the instrument to

power supply.

⚫

Use electric wires of appropriate load. All loading wires should be capable

of bearing maximum short-circuit current of power supply without
overheating. If there are multiple electronic loads, each pair of the power
cord must be capable of bearing the full-loaded rated short-circuit output
current.

⚫

Ensure the voltage fluctuation of mains supply is less than 10% of the

working voltage range in order to reduce risks of fire and electric shock.

⚫

Do not install alternative parts on the instrument or perform any

unauthorized modification.

⚫

Do not use the instrument if the detachable cover is removed or loosen.

⚫

To prevent the possibility of accidental injuries, be sure to use the power

adapter supplied by the manufacturer only.

⚫

We do not accept responsibility for any direct or indirect financial damage

or loss of profit that might occur when using the instrument.

⚫

This instrument is used for industrial purposes, do not apply this product to

IT power supply system.

Summary of Contents for IT-M3300 Series















































































































Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands

ITech IT-M3300 Series, Programming Manual

Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands