ITech IT-M3300 Series Programming Manual Download | Manualshive

Page: 26 / 110

background image

Status Commands

Copyright © Itech Electronic Co., Ltd.

3

Query syntax

STATus:OPERation:PTRansition?

Returns

NR1

STATus:QUEStionable[:EVENt]?

This  command  can  be  used  to  read  the  value  in  query  event  register.The
electronic  load  will  return  a  decimal  number  corresponding  to  the  binary
weighted  sum  of  each  unit  digit  of  register.  These  digits  will  be  latched.  After
executing this

command, the query event register will be cleared.

Syntax

STATus:QUEStionable[:EVENt]?

Arguments

None

Example

STAT:QUES?

Returns

NR1

STATus:QUEStionable:CONDition?

This command is used to read the value of query condition register and
gets the status of electronic load.

Syntax

STATus:QUEStionable:CONDition?

Arguments

None

Example

STAT:QUES:COND?

Returns

NR1

STATus:QUEStionable:ENABle <n>

This command edits the enable register value of query event. In query, the
electronic load will return a decimal number representing the binary weighted
sum of the enable register.

«
...
24
25
26
27
28
...
»

Summary of Contents for IT-M3300 Series















































































































Reviews:

No comments

Related manuals for IT-M3300 Series

Brand: TANDBERG Pages: 53

Brand: E+E Elektronik Pages: 32

POCKET COLORIMETER II

Brand: Hach Pages: 188

Brand: OHAUS Pages: 19

Brand: OHAUS Pages: 54

Brand: Zenner Pages: 2

Brand: TC Electronic Pages: 20

Brand: Vega Pages: 20

Brand: Vega Pages: 16

Brand: Vega Pages: 2

Brand: Topcon Pages: 62

Brand: Keithley Pages: 31

Brand: Keithley Pages: 63

Brand: Keithley Pages: 18

Brand: Keithley Pages: 73

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: Olympus Pages: 2

RP050B-S1/2 Series

Brand: MST Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands