ITech IT-M3300 Series Programming Manual Download

Page: 79 / 110

Trace Commands

Returns

NR1

TRACe:FEED:CONTrol <NEVer|NEXT|ALWays>

This command is used to select cache control. Select NEVer, Save to Cache is

disabled; select NEXT, save process starts and will stop when the cache is filled

in. Select ALWays. After cache is filled in, circulate the cache.

Syntax

TRACe:FEED:CONTrol <NEVer|NEXT|ALWays>

Arguments

NEVer|NEXT|ALWays

Default value

NEVer

Example

TRAC:FEED:CONT NEXT

Query syntax

TRACe:FEED:CONTrol?

Returns

NEVer|NEXT|ALWays

TRACe:FEED[:SELected]<BOTH|VOLTage|CURRent>

This command selects the reading source saved in the cache. If VOLTage is

selected, the voltage reading is saved in cache; if CURRent is selected, the

current reading is saved in cache. If BOTH is selected, both voltage and current

are saved in cache when saving is executed.

Syntax

TRACe:FEED[:SELected]<BOTH|VOLTage|CURRent>

Arguments

BOTH|VOLTage|CURRent

Default value

VOLTage

Summary of Contents for IT-M3300 Series















































































































Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands

ITech IT-M3300 Series, Programming Manual

Search results

Summary of Contents for IT-M3300 Series

Reviews:

Related manuals for IT-M3300 Series

Brands by name

Popular brands