ITC VISIONS 3000, User Manual

Page: 16 / 36

Q
EC
PH 250
1.05
7.6
A F02
5.4bar
B
1 4 EC 31% PH 86%
mS
m3h
Q
EC
PH 250
1.05
7.6
A F02
5.4bar
B
CAL
PROG
ALM
CONT
HIST
AUX
mS
m3h
ENT
ENT
3.8.1.2 FLOWMETER CALIBRATION
PRES
TIME
PUMP
PH
EC
Q
Change Units by pr/- and validate by ENT:
m3h
: Water Flow in m3/h
Dosage Flow in l/h
gal
: Water Flow in GPM
Dosage Flow in GPH
3. CONFIGURATION
K-Factor
(pulses/litre or pulses/gallon):
Please refer to Manual Instructions of Flow Meter in accordance with the type and size of the pipes where it is
installed.
Change Value by pr/- and validate by ENT
W.COUNTER
: liters/pulse of a water counter
Q=0
: time when it´s considered there is no flow.
Q
EC
PH 250
1.05
7.6
A F02
5.4bar
B
CAL
PROG
ALM
CONT
HIST
mS
m3h
AUX
ENT
Change Units by pr/- and
validate by pressing ENT.
CTRL. PH: ACID/ALKALINE
: defines if the pH Control is executed by adding Acid (ACID) or Base (ALKALINE)
EC:1.40:
defines the EC buffer used. It can be modified by pr/-
PH: 4 Time 60s
: defines the pH Buffer and the Stabilization Time for the Sensor Calibration.
3.8.1.3.1 Calibration set up
Q
EC
PH 250
1.05
7.6
A F02
5.4bar
B
CAL
PROG
ALM
CONT
HIST
AUX
mS
m3h
Q
EC
PH 250
1.05
7.6
A F02
5.4bar
B
1 4 EC 31% PH 86%
mS
m3h
3.8.1.3 EC AND PH CALIBRATION
WATER CONTROLLER 3000
USER'S MANUAL
K-factor
(pulse/liter)
Diameter(Inch)
Diameter (mm)
K-factor
(pulse/gallon)
32 75 160 40 90 200 50 110 250 63 125 315 400
1 2 ½ 6 1 ¼ 3 8 1 ½ 4 10 2 5 12 16
78.5 9.2 2.2 45 6.6 1.3 27.4 4.3 0.74 15.7 3.6 0.52 0.27
297 35 8.2 170 25 4.8 104 16.3 2.8 59.5 13.6 2.0 1
Flowmeter Burkert 8020
Flowmeter GF 2536
32 75 160 40 90 200 50 110 250 63 125 315 400
1
2 ½ 6 1 ¼ 3 8 1 ½ 4 10 2 5 12 16
57 12.3 2.0 30 7.6 1.4 18.6 5.3 0.8 15.6 4.0 0.4 0.2
214
47 7.7 113 29 5.2 71.5 20 3.0 59 15.1 1.6 0.9
K-factor
(pulse/liter)
Diameter(Inch)
Diameter (mm)
K-factor
(pulse/gallon)
CHECK
FIRMWARE
SETUP
ENT
SET UP
Kp B: 10
CTRL. PH: ACID
NUM PROG.: 1
EC: 1.40
PH: 4 TIME: 60S
Kp A: 10
Q
Units:
Qtype: HIGH
K-Factor: 2.00
m3h
Q
Units: m3h
Qtype: HIGH
K-Factor: 2.00
Q
Units: m3h
Qtype:
K-Factor: 2.00
HIGH
To configure a water counter, select LOW.
Q
Units: m3h
Qtype:
W.COUNTER: 000.0 l/p
TIME Q=0: 300s
LOW
Q
Units: m3h
Qtype: LOW
W.COUNTER:
TIME Q=0: 300S
000.0 l/p
Q
Units: m3h
Qtype: LOW
W.COUNTER:000.0 l/p
TIME Q=0: 300S
Q
Units: m3h
Qtype:
K-Factor: 2.00
HIGH
16