manualshive.com logo in svg

Ironman4x4 SLIDE-AWAY, Installation Manual

Share
Download
Ironman4x4 SLIDE-AWAY Installation Manual Download Page 14

Page 14 of 15

SLIDE-AWAY

Installation Guide

©Copyright 2021 Ironman 4x4 Pty Ltd. No part of this publication may be reproduced or replicated without the prior written consent of Ironman 4x4 Pty Ltd

Remote Controller Function Instructions

LED Indicator Light

Close Tonneau Cover
Open Tonneau Cover
Turn On Tub Interior Light
Turn Off Tub Interior Light

Buttons

Name

Description

Close Tonneau 

Cover 

1. Press the button to start closing the Tonneau 
Cover if it is in static mode.
2. Press the button to stop the Tonneau Cover if it is 
in operating mode.

Open Tonneau 

Cover 

1.Press the button to start opening the Tonneau 
Cover if it is in static mode.
2. Press the button to stop the Tonneau Cover if it is 
in operating mode.

Turn off tub interior 

Light 

Press the button to turn off the tub interior light.

Turn on tub interior 

Light 

1. Press the button to turn on the tub interior light if      
the light is off. 
2. Press the button to switch to the next level 
brightness if the light is on (3 level brightness cycle 
switch).

Summary of Contents for SLIDE-AWAY
















Reviews:

No comments

Brands by name

Popular brands

Load more brands