IPX VE-3500 Installation & Operation Manual Download Page 12

Page: 12 / 94

3. INSTALLATION

Please follow the instructions below to set up the system.

3.1 UPDATING SYSTEM SOFTWARE

If the system software of the ipxserv

needs to be upgraded, please take the following steps to

safely process it.

Important: Before carrying out the following procedures, please ensure the SD card is

working and the file of the system firmware is intact

1. Format an SD card using the FAT16 format if it is unformatted; there are no limitations to an SD

card’s capacity.

2. Create a directory named “IPXSERV” in the SD card if it does not exist.

3. Copy the file of UPDATE.BIN to the IPXSERV-directory.

4. If the Video Server is running, please power it off first.

5. Insert the SD CARD into the Video Server.

6. Remove the Ethernet cable from the RJ-45 port and then power on the Video Server.

7. In 5 to 10 seconds, a message reading "UPDATE PROCESSING" will show up on the screen on

a blue background; if not, please check out steps 1 to 6 carefully or else inform your technical

support while ignoring the following steps.

8. DO NOT power off the Video Server while this update process is running until the message

"UPDATE OK RESET PLEASE" appears on the screen; it might take 15 to 30 seconds to

appear.

9. If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET

PLEASE", please write down the error messages shown on the screen and inform your

technical support, while ignoring the following steps.

10. Power off the Video Server when this update process is finished, then remove the SD card from

the Video Server.

11. Reconnect the Ethernet cable to the RJ-45 port if necessary.

Summary of Contents for VE-3500































































































Search results

Summary of Contents for VE-3500

Reviews:

Related manuals for VE-3500

Brands by name

Popular brands

IPX VE-3500, Installation & Operation Manual

Search results

Summary of Contents for VE-3500

Reviews:

Related manuals for VE-3500

Brands by name

Popular brands