inVENTer iV-Twin+ Installation And Operating Instructions Manual Download

Page: 21 / 25

SCOPE OF DELIVERY

ACCESSORIES AND SPARE PARTS

Ventilation System iV-Twin+

•

Installation and Operating Instructions

Ventilation System iV-Twin+

•

Installation and Operating Instructions

Scope of delivery

Standard components

All standard components are also available as spare parts.

Component

Product Number

iV-Twin+

1001-0203

External closure Weather protection hood incl. sealing strips

Weather protection hood-Flex Twin+, white ‒ RAL 9016

1508-0113

Weather protection hood-Flex Twin+, grey ‒ RAL 9006

1508-0114

Weather protection hood-Flex Twin+, Nord ‒ RAL 7011

1508-0115

Weather protection hood-Flex Twin+, anthracite ‒ RAL 7016

1508-0128

Weather protection hood-Flex Twin+, special colour

1508-0116

Wall sleeve with Styrofoam disks and mounting wedges

Wall sleeve R-D200x495

1506-0070

Wall sleeve R-D200x745

1506-0071

Heat accumulator insert
Heat storage unit iV-Twin+ insert

[incl. separating element 765 mm]

1507-0023

Inner cover

Inner cover Flair Twin+ V-223x233, white

1505-0040

Accessories and Spare Parts

To order accessories for your ventilation system, please contact your local factory

representative.

Accessories

Component

Product Number

Dust filter iV-Twin+ (1 Set)

1004-0192

Pollen filter iV-Twin+ (1 Set)

1004-0193

Activated carbon filter iV-Twin+ (1 Set)

1004-0194

Sound protector SPR iV-Twin+ (2 x)

1004-0189

Sound protection insert iV-Twin+ (2 x)

1004-0190

Component

Product Number

Round cable LiYY-O 3x0,75 (33m)

1004-0020

Mounting wedge set (block with 16 wedges)

3009-0012

Styrofoam disk R-D196x30 (for wall sleeve)

3007-0088

Simplex 365 incl. wall sleeve R-D200

1506-0090

Simplex 490 incl. wall sleeve R-D200

1506-0091

Wall mounting block D230 V-280x249x120

3008-0078

Styrofoam disk R-D230x30 (for wall mounting block)

3007-0106

WEH R-D200 Extension Set

1004-0176

Insulation dowel set

1004-0067

Spare Parts

Component

Product Number

Heat accumulator iV-Twin+ half cylinder

2002-0075

Fan unit iV-Twin+ half cylinder

2007-0035

Separator iV-Twin+ R-D200x765

2002-0077

Connecting cable iV-Twin+

2007-0036

Base plate IB Flair V-233x233

2003-0223

Cover IB Flair Twin V-233x233

2003-0231

Base plate spacer IB 25mm white

3006-0151

Base plate WSH-Nova R/Flex, white– RAL 9010

3006-0272

Base plate WSH-Nova R/Flex, grey– RAL 7004

3006-0274

Cover WSH-Flex, white – RAL 9016

2004-0202

Cover WSH-Flex, grey – RAL 9006

2004-0203

Cover WSH-Flex, Nord – RAL 7011

2004-0204

Cover WSH-Flex, anthracite – RAL 7016

2004-0210

Cover WSH-Flex, special colour

2004-0205

Separating insert WSH-Flex Twin+

3006-0303

Summary of Contents for iV-Twin+


























Search results

Summary of Contents for iV-Twin+

Reviews:

Related manuals for iV-Twin+

Brands by name

Popular brands

inVENTer iV-Twin+, Installation And Operating Instructions Manual

Search results

Summary of Contents for iV-Twin+

Reviews:

Related manuals for iV-Twin+

Brands by name

Popular brands