background image

6.4 

Install fan units and heat accumulators

Prerequisite: 

The heat accumulator plug-in unit has been removed.

6.5 

Mount the cover of the inner cover

Prerequisite: 

The heat storage module is installed.

34

35

CLEANING AND MAINTENANCE

CLEANING AND MAINTENANCE

Ventilation System iV-Twin+ 

 Installation and Operating Instructions

Ventilation System iV-Twin+

 

 Installation and Operating Instructions

 

Pull out the heat accumulator half cylinders from 

the wall sleeve by the handle.

NOTE: 

In case of breakage/damage of the 

ceramic heat accumulator,

the heat accumulators will lose their function!

•  Do not throw ceramic heat accumulators.

•  Store the ceramic heat storage tank 

vertically outside the wall sleeve.

NOTE:

 Incorrect cleaning of the heat 

accumulator leads to damage 

of the 

insulation at the heat accumulator.

•  Never clean in the dishwasher.

 

Clean both cylinders under running hot water.

 

Let the water drip off.

 

Wait until the heat accumulator is completely dry. 

 

You have cleaned the heat accumulator.

6.3 

Cleaning the heat accumulator

Prerequisite: 

The ventilation unit is disconnected from the power 

supply. The fan unit is removed. (

 6.2)

 

Push the heat storage tank half cylinders to the 

right and left of the separating element from 

the interior up to the stop in the direction of the 

weather protection hood.

Make sure 

that the handle points in the direction 

of the interior.

Make sure

 that the fan BUS protrudes into the 

interior.

 

Push the fan units back into the wall sleeve so that 

the filter faces the heat accumulator.

 

Place the cover on the four spacers. 

Make sure

 

that the position arrows on the back of the cover 

point upwards. 

Check: The inVENTer logo is at the bottom right.

Ensure

 that the separator is inserted into the inner 

cover holder.

 

Press the latching lugs on the spacers inwards.

 

You have installed the inner cover.

 

Insert one of the cables into the fan so that all lines 

are in the same chamber of the wall sleeve.

 

Reconnect the plugs on the fan to the sockets of 

the connecting cable.

 

You have reinstalled the heat accumulators and 

fan units.

 

Slide the cover onto the spacers.

All spacers will engage noticeably.

1

2

2

3

4 x CLICK

1

2

1

Summary of Contents for iV-Twin+


























Reviews: