About This Manual
2015-MNU-000009
iv
•
Use one hand, when possible, to connect or disconnect signal cables to prevent a
possible shock from touching two surfaces with different electrical potentials.
•
This product is equipped with a three-wire power cord and plug for user safety. Use the
power cord with a properly Grounded electrical outlet to avoid electric shock.
Motherboards, adapters, and disk drives are sensitive to static electricity discharge. These
devices are wrapped in antistatic bags to prevent this damage. Take the following
precautions:
•
If you have an antistatic wrist strap available, use it while handling the device.
•
Do not remove the device from the antistatic bag until you are ready to install the device in
the system unit.
•
With the device still in its antistatic bag, touch it to a metal frame of the system.
•
Grasp cards and boards by the edges. Hold drives by the frame. Avoid touching the solder
joints or pins.
•
If you need to lay the device down while it is out of the antistatic bag. Lay it on the
antistatic bag. Before picking it up again, touch the antistatic bag and the metal frame of
the system unit at the same time.
•
Handle the devices carefully to prevent permanent damage.
Battery Replacement Safety
This server is provided with an internal Lithium battery or battery pack. There is a danger of
explosion and risk of personal injury if the battery is incorrectly replaced or mistreated.
For more information about battery replacement or proper disposal, contact an authorized
reseller or your authorized service provider.
This server contains an internal Lithium Manganese Dioxide, or a Vanadium Pentoxide, or an
alkaline battery pack. There is risk of fire and burns if the battery pack is not handled properly.
To reduce the risk of personal injury:
•
Do not attempt to recharge the battery.
•
Do not expose to temperatures higher than 70°C.
•
Do not disassemble, crush, puncture, shorten external contacts, or dispose in fire or
water.
•
Replace only with the spare parts designated for this product.
Summary of Contents for N800G3
