background image

8

TruPortal IP-based Single Door Controller Quick Reference

Figure 11: IPSDC LEDs and Switches

Callout

Description

State

LEDs

1

D85 Power On

ON: power is present

2

D14 Offline

Normally OFF

3

D15 Address RX

Normally OFF

4

D16 Badge Activity

Normally OFF; flashes when badge is read

5

D17 Database Pending

Flashes while waiting to receive database from host

6

D18 File System Active

Normally OFF

7

D19 Watchdog

Flashes one beat per second if watchdog is healthy

8

D20 Flash Upload

ON when IPSDC is booting up

9

D21 Shutdown Request

Normally OFF/Flashes and then ON

10

D33 Strike Activated

ON during strike activation

11

D24 FACP (not supported by IPSDC)

ON = contact open

12

D25 Door Contact

ON = contact closed; OFF = contact open; Flashing = fault

13

D26 Door REX

ON = contact closed; OFF = contact open; Flashing = fault

14

DS and DS5 Link

ON = link activity; OFF = no activity. Flashing = network activity

15

DS4 and DS8 Collision

ON = Collision

16

DS3 and DS7 Full Duplex

ON = Full duplex; OFF = Half duplex

17

DS2 and DS6 100/10 Mbps

ON = 100 Mbps; OFF = 10 Mbps

Switches

18

SW4 Boot Mode

Manually enables the ICT.

19

SW5 Hardware Reset

Reboots the IPSDC.

20

SW6 Shutdown Request

Initiates Safe Shutdown of the IPSDC. 

21

SW7 Restore Defaults

Returns configuration to factory defaults.

Summary of Contents for TruPortal TP-ADD-1DIP










Reviews: