background image

The following chart provides the device numbers that will be reported for trouble conditions.

KEYPAD

PARTITION

1

2

3

4

5

6

7

8

1

192

193

194

195

196

197

198

199

2

200

201

202

203

204

205

206

207

3

208

209

210

211

212

213

214

215

4

216

217

218

219

220

221

222

223

5

224

225

226

227

228

229

230

231

6

232

233

234

235

236

237

238

239

7

240

241

242

243

244

245

246

247

8

248

249

250

251

252

253

254

255

NX1192E MAXIMUM WIRE RUN

(Note:  These numbers are for one keypad at the end of the wire. When connecting more

than one keypad to the end of the wire, a heavier gauge wire will be required.)

WHEN CONNECTED TO NX8-E

WHEN CONNECTED TO NX-320

Length in feet

Wire Gauge

Wire Gauge

250'

24

22

500

20

18

1000

18

16

1500

16

14

2500

14

12

SPECIFICATIONS

OPERATING POWER

12 VDC Regulated
Supplied by NX8-E or NX-320

OPERATING TEMPERATURE

32 to 120 degrees F

CURRENT DRAW

110 mA Maximum
75 mA without Sounder

LCD KEYPAD DIMENSIONS

6.4" Wide
5.3" High
1.0" Deep

SHIPPING WEIGHT

2 lbs.

CADDX CONTROLS, INC.

1420 N MAIN STREET;  GLADEWATER, TEXAS  75647

TOLL FREE 800-727-2339

FAX 903-845-6811

www.caddx.com

NX1192E INSTALLATION MANUAL
NX1192EIA02

REV. A   (04-01-02)

Summary of Contents for NX1192E

















Reviews: