background image

13

DISPLAYS IN THE PARTITIONING MASTER MODE

Armed and Ready Status
The LCD screen will display the Armed and Ready status of ALL eight (8) partitions if any or
all of the areas is armed or not ready.

This display is reflecting all 8 areas are Ready, and Area
5 is disarmed.
NOTE: If a number is flashing on the armed line, that

area is armed Instant.  If a number is flashing on the ready line, that area is ready to be Force
Armed
.

If ALL areas are disarmed and ready to arm, this display
will appear on the LCD screen.

Arming and Disarming Multiple Partitions
To arm/disarm multiple partitions, enter a code that has arm/disarm authority for ALL of the
partitions to be armed/disarmed.  The following display will appear on the LCD screen.

The numbers on the top line represent the disarmed
areas to which this code has access.  The numbers on
the bottom line represent the areas that are armed. Refer
to the following table for possible conditions.

LCD DISPLAY FOR AREA

TOP LINE OVER BOTTOM LINE

CONDITION

Blank
Blank

Area Not Used or Authorized

Dash (-)
Dash (-)

Area Not Ready

Flashing
Dash (-)

Area Ready to Force Arm

Dash (-)
Flashing

Area Armed Instant

Area #
Dash (-)

Area Disarmed & Ready to Arm

Dash (-)
Area #

Area is Armed

‹

 

To disarm all of the areas, press the [

N

] up scroll key.

‹

 

To arm all of the areas, press the down scroll [

O

] key.

‹

 

To toggle a single area between the armed and disarmed conditions, press [

7

]

[Area number].  For example, if Area 4 is armed, [

7

] [4] will disarm Area 4.  If Area

4 is disarmed, [

7

] [4] will arm it.

‹

 

To control the individual areas, refer to the following section “Operating Individual
Areas in the Multi-Partition Mode”.

Operating Individual Areas in the Multi-Partition Mode
Enter a code that is a valid arm/disarm code for the area you wish to operate.  The following
display will appear:

Only the areas authorized by this code will appear.

ƒ

 

To toggle between the armed and disarmed states on an individual area, press [

7

]

[Area Number].

5HDG\

$UPHG

6\VWHP5HDG\

7\SHFRGHWRDUP

'LVDUP

 



$UP



'LVDUP

 



$UP



Summary of Contents for NX1192E

















Reviews: