manualshive.com logo in svg

Interlogix Alliance AL-4017, Installation Manual, Page: 27 / 32

Share
Download
Interlogix Alliance AL-4017 Installation Manual Download Page 27

17

Formulas

Table 4

 provides the formulas to calculate battery requirements.

Table 4.

Battery calculation formulas

Formula

Calculation

Result

1

Total standby current x Conversion factor x Required hours in standby
                           mA          x     .001Amp/mA     x                             hours

Ah standby Amp-hours
                                  

2

Total alarm current x Conversion factor x Required minutes in alarm x Conversion factor

                       mA   x  .001Amp/mA          x                       minutes   x .0167 hours/min.

Ah alarm Amp-hours
                                  

3

Total active current x Conversion factor x Required seconds active x Conversion factor
                       mA   x   .001Amp/mA      x                       seconds  x .000278 hours/sec.

Ah active Amp-hours
                                  

4

Standby Amp-hours + Alarm Amp-hours + Active Amp-hours
                                         +                                     +                             

Minimum battery power  

required
                                   Ah       

5

Minimum battery power required x Battery capacity derating coefficient
                                                                   x                                1.15        

Total standby battery 

required
                                    Ah

Summary of Contents for Alliance AL-4017

































Reviews:

No comments