Intel SCB2 - Server Board Motherboard Product Manual Download Page 97

Page: 97 / 108

7 Regulatory and Integration Information

Product Regulatory Compliance

Product Safety Compliance

The SCB2 complies with the following safety requirements:

•

UL 1950 - CSA 950 (US/Canada)

•

EN 60 950 (European Union)

•

IEC60 950 (International)

•

CE – Low Voltage Directive (73/23/EEC) (European Union)

•

EMKO-TSE (74-SEC) 207/94 (Nordics)

•

GOST R 50377-92 (Russia)

Product EMC Compliance

The SCB2 has been has been tested and verified to comply with the following electromagnetic
compatibility (EMC) regulations when installed in a compatible Intel

host system. For

information on compatible host system(s), contact your local Intel representative.

•

FCC (Class A Verification) – Radiated & Conducted Emissions (USA)

•

ICES-003 (Class A) – Radiated & Conducted Emissions (Canada)

•

CISPR 22 (Class A) – Radiated & Conducted Emissions (International)

•

EN55022 (Class A) – Radiated & Conducted Emissions (European Union)

•

EN55024 (Immunity) (European Union)

•

CE – EMC Directive (89/336/EEC) (European Union)

•

GOST R 29216-91 Radiated & Conducted Emissions (Russia)

•

GOST R 50628-95 Immunity (Russia)

•

VCCI (Class A) – Radiated & Conducted Emissions (Japan)

•

AS/NZS 3548 (Class A) – Radiated & Conducted Emissions (Australia / New Zealand)

•

RRL (Class A) Radiated & Conducted Emissions (Korea)

•

BSMI (Class A) Radiated & Conducted Emissions (Taiwan)

Product Regulatory Compliance Markings

This product is provided with the following Product Certification Markings.

•

cURus Recognition Mark

•

CE Mark

•

Russian GOST Mark

•

Australian C-Tick Mark

•

Taiwan BSMI Certification Number 3902I904 and BSMI EMC Warning

Summary of Contents for SCB2 - Server Board Motherboard













































































































Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands

Intel SCB2 - Server Board Motherboard, Product Manual

Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands