Intel SCB2 - Server Board Motherboard Product Manual Download Page 90

Page: 90 / 108

Intel Server Board SCB2 Product Guide

Problems with Application Software

If you have problems with application software, do the following:

Verify that the software is properly configured for the system. See the software installation and
operation documentation for instructions on setting up and using the software.

Try a different copy of the software to see if the problem is with the copy you are using.

Make sure all cables are installed correctly.

Verify that the server board jumpers are set correctly. See Chapter 5.

If other software runs correctly on the system, contact your vendor about the failing software.

If the problem persists, contact the software vendor’s customer service representative for help.

Bootable CD-ROM Is Not Detected

Check the following:

Is the BIOS set to allow the CD-ROM to be the first bootable device?

Check cable connections.

Verify CD is bootable in another known good CD-ROM drive. (Especially if the CD
is a copy.)

Summary of Contents for SCB2 - Server Board Motherboard













































































































Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands

Intel SCB2 - Server Board Motherboard, Product Manual

Search results

Summary of Contents for SCB2 - Server Board Motherboard

Reviews:

Related manuals for SCB2 - Server Board Motherboard

Brands by name

Popular brands